# generated by Slic3r 1.1.7 on Fri Mar 13 18:38:55 2015
avoid_crossing_perimeters = 0
bed_size = 214,234
bed_temperature = 30
bottom_solid_layers = 0
bridge_acceleration = 5000
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 50
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 4000
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = \n\n
external_perimeter_speed = 50
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0.6
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 0%
fill_pattern = rectilinear
first_layer_acceleration = 4000
first_layer_bed_temperature = 55
first_layer_extrusion_width = 0.6
first_layer_height = 0.23
first_layer_speed = 30
first_layer_temperature = 205
g0 = 0
gap_fill_speed = 50
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 5000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.6
infill_first = 0
infill_only_where_needed = 0
infill_speed = 50
interface_shells = 0
layer_gcode = 
layer_height = 0.12
max_fan_speed = 100
min_fan_speed = 40
min_print_speed = 5
min_skirt_length = 20
notes = 
nozzle_diameter = 0.34
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 4000
perimeter_extruder = 1
perimeter_extrusion_width = 0.6
perimeter_speed = 50
perimeters = 1
post_process = 
print_center = 107,117
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 6
retract_length_toolchange = 10
retract_lift = 0.5
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 15
seam_position = aligned
skirt_distance = 3
skirt_height = 1
skirts = 8
slowdown_below_layer_time = 10
small_perimeter_speed = 50
solid_fill_pattern = rectilinear
solid_infill_below_area = 40
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0.6
solid_infill_speed = 50
spiral_vase = 1
standby_temperature_delta = -5
start_gcode = \n
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.6
support_material_interface_extruder = 1
support_material_interface_layers = 5
support_material_interface_spacing = 5
support_material_interface_speed = 50
support_material_pattern = rectilinear
support_material_spacing = 8
support_material_speed = 50
support_material_threshold = 30
temperature = 195
thin_walls = 0
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 50
top_solid_layers = 0
travel_speed = 150
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 1
z_offset = 0